SHMU
ASME S · H · M · U

Code-built boilers and vessels

National Board R

Code repairs and alterations

Autoflame
Autoflame

Factory-authorized Tech Center

Limpsfield
Limpsfield

Factory-authorized Burner Tech Center

McKenna flame
Since 1921

Fifth generation, family-owned

How Boiler Turndown Ratio Affects Boiler Performance

boiler-turndown-ratio

Boiler turndown ratio is a burner’s maximum firing rate divided by its minimum firing rate, and it decides whether the boiler can follow a light load smoothly or has to cycle on and off. Too little turndown means short cycling, with purge losses and wear on every start; very deep turndown can cost efficiency and is harder to reach on ultra-low NOx burners. McKenna Boiler Works, Inc. builds boilers in California with each burner matched to the boiler and the emissions limit, and this post explains the math, the trade-offs, and how much turndown a plant actually needs.

How is turndown ratio calculated?

Divide the maximum firing rate by the minimum. The minimum firing rate, as a share of maximum, is 1 divided by the ratio.

Turndown ratioMinimum firing rateMinimum on a 10 million Btu/hr burner
3:133%3.3 million Btu/hr
4:125%2.5 million Btu/hr
5:120%2.0 million Btu/hr
10:110%1.0 million Btu/hr

Two cautions. First, the ratio on a data sheet is for a specific fuel, at a specific emissions level, with the burner set up a certain way. Ask for the turndown the burner will deliver at your permitted NOx limit and on your fuel. Second, compare the minimum firing rate with your plant’s minimum load, which is often a night or weekend load far below the design peak.

What happens when turndown is too low?

When the load falls below the burner’s minimum firing rate, the boiler makes more heat than the load uses. Pressure or temperature rises to the operating control’s cut-out, the burner stops, the boiler coasts down, and the burner restarts. That is short cycling, often several cycles an hour or more on light-load days.

Every cycle costs something:

  • Purge losses. The flame safeguard runs a pre-purge before every ignition and a post-purge after every shutdown, blowing air through the hot boiler and out the stack. That air carries heat away even though no fuel is burning.
  • Thermal cycling. Repeated heating and cooling stresses tube joints and refractory.
  • Wear on components. Ignition transformers, fuel valves, actuators, and the flame safeguard all have finite cycle lives.
  • Control swings. Steam pressure or water temperature saw-tooths between the cut-in and cut-out, which some processes do not tolerate.

Is more turndown always better?

Usually more turndown helps, but there are trade-offs:

  • Excess air at low fire. Many burners run more excess air at low fire to keep the flame stable, which raises the stack loss share at that point. Parallel positioning controls with O2 trim hold the air-fuel ratio closer to target across the range.
  • Shell losses. Radiation and convection loss from the boiler shell is roughly constant in Btu/hr, so at 10% firing it is a larger share of input than at full fire.
  • Ultra-low NOx burners. Burners built to meet the lowest California NOx limits often have less turndown than conventional burners, because holding very low NOx and low CO across a wide range is harder. The air district’s limit can therefore set a floor on minimum firing.
  • Cost. High-turndown burners and their controls cost more, so the extra range should match a real load.

How much turndown does a plant need?

Work from the load profile. List the peak load, the normal operating load, and the lowest load the plant runs at for long periods. If the lowest load is above the boiler’s minimum firing rate, turndown is adequate. If it is below, the options are:

  • A burner with more turndown, through a retrofit or a controls upgrade.
  • Two or more smaller boilers with lead-lag sequencing, so one boiler carries light loads and others start as the load rises. This also gives redundancy.
  • A smaller boiler for summer or weekend loads alongside the main boiler.
  • Wider operating control differentials, which cut cycles but widen pressure swings.

The boiler sizing calculator is a starting point for matching boiler size to the load.

What to check

  1. Count burner starts per hour on a light-load day, from the controls’ history or by watching. Frequent starts mean the minimum firing rate is above the load.
  2. Read the burner’s data plate and the last tuning report for the maximum and minimum firing rates actually set.
  3. Check O2 and CO at low fire as well as high fire during tuning.
  4. Log steam pressure or water temperature swings and compare with what the process needs.
  5. Confirm the permitted NOx limit before asking for more turndown on an existing burner.
  6. Leave the flame safeguard’s purge timing alone. It is a safety function. Reduce cycling by fixing turndown or sequencing; never by shortening purge or bypassing controls. If the flame safeguard ever fails to lock out on a test, shut the burner off manually and call for service.

Common questions

What does a 10:1 turndown ratio mean?

The burner can fire as low as 10% of its maximum rate. On a 10 million Btu/hr burner, that is 1 million Btu/hr, so the boiler can follow loads down to that level without cycling off.

How many burner cycles per hour is too many?

There is no single number, but a burner that starts several times an hour on a steady light load is short cycling. Check the burner and flame safeguard manufacturer’s guidance and look at what is causing it.

Why do ultra-low NOx burners have less turndown?

Very low NOx depends on holding a lean, carefully mixed flame at low temperature. Keeping that flame stable with low CO over a wide firing range is difficult, so the usable range at the permitted NOx limit is often narrower.

Is it better to buy two smaller boilers than one large one with high turndown?

Two smaller boilers give redundancy and follow very light loads well, but cost more to install and take more room. One boiler with high turndown is simpler. The load profile and how critical the steam is decide it.

Can I improve turndown on my existing boiler?

Often, through a burner retrofit or a controls upgrade, as long as the new range meets the air district’s limit. A technician should review the burner, the controls, and the permit first.

McKenna Boiler Works, Inc. builds turnkey boiler systems in California and services and repairs other brands. McKenna installs, sets up, and tunes burners and controls from any manufacturer, including one an engineer has already specified, and can recommend Limpsfield, Autoflame, or Power Flame. For more turndown or better sequencing on an existing boiler, see controls and efficiency upgrades; for retrofits to meet a lower NOx limit, see ultra-low NOx retrofits. Call (323) 987-1816.

Need help with your boiler? McKenna Boiler Works, Inc. builds, installs, and services industrial boilers across California, and services and repairs other brands. Call (323) 987-1816 or request service.

Firetube boiler tubesheet with the old tubes removed during a McKenna retube

Retube or Replace a Firetube Boiler: How to Decide

Leaking or thinning tubes do not always mean a new boiler. Here is how to decide between a retube and

Read article →

Welding at a firetube boiler tubesheet

Boiler R Stamp Repair: What It Involves and When You Need One

Replacing tubes or welding on a shell, tubesheet, furnace, or nozzle is code work under the National Board Inspection Code.

Read article →

McKenna feedwater tank on a stand with duplex feed pumps below and water softeners beside it

Water Treatment and Its Impact on Industrial Boiler Reliability

Scale, oxygen pitting, and carbonic acid shorten boiler life. How each mechanism works, what a treatment program includes, and who

Read article →

Have a question about your boiler?

A live person answers (323) 987-1816 24/7.

Serving all of California · Family-owned since 1921

Request a Quote

Tell us what you need.

Fill in what you know. A McKenna engineer will review it and get back to you. Need help now? Call (323) 987-1816.