Good steam trap maintenance means finding failed traps by testing each trap with ultrasound and temperature on a schedule, logging the results, and fixing failed-open traps on high-pressure lines first. A trap that blows steam wastes fuel and overloads the condensate system; a trap that holds condensate starves equipment of heat and causes water hammer. McKenna Boiler Works, Inc. performs steam trap audits, and this post explains how traps work, how they fail, and how to run a trap program.
What does a steam trap do?
A steam trap is an automatic valve that lets condensate, air, and other non-condensable gases out of the steam system while holding live steam in. Steam gives up its heat by condensing, and the water it leaves behind has to go. If condensate stays in a heat exchanger, it covers the heating surface and heat transfer falls. If air stays, it insulates the surface and lowers the effective steam temperature. If condensate pools in a steam main, fast-moving steam can pick up a slug of water and slam it into a fitting, which is water hammer, and it can crack valves and strainers.
How does each trap type work and fail?
| Trap type | How it works | Typical use | Common failure |
|---|---|---|---|
| Float and thermostatic (F&T) | A float rises with condensate level and opens the valve; a thermostatic element vents air at startup | Heat exchangers and jacketed vessels with changing loads | Worn seat leaks steam; collapsed float or failed vent holds condensate or air |
| Inverted bucket | Steam fills the bucket and floats it closed; condensate sinks it open | Drip legs on mains, process equipment | Loses its water seal (prime) and blows steam |
| Thermostatic (bellows or bimetal) | Opens when the condensate cools below steam temperature | Tracing, small loads, air venting | Holds back condensate if it fails closed; can back up a process load |
| Thermodynamic (disc) | Flash steam above the disc snaps it closed; cooler condensate lets it open | Drip legs, tracing | Worn disc cycles rapidly or blows through; sensitive to high back pressure |
The right type depends on the application, the pressure, and the load. A trap that is the wrong type or size for its job can look failed when it is just misapplied.
What happens when a trap fails open or closed?
Failed open (blowing through). Live steam passes into the condensate return. The return runs hotter than it should, condensate flashes in the receiver, and you see a heavy steam plume at the vent. Hot condensate can flash at the feed pump suction and cavitate the pump. Steam vented at the receiver leaves the system, so makeup water rises, and every gallon of makeup brings more hardness and oxygen for the water treatment program to handle. The boiler fires harder to carry the same load. Losses grow with steam pressure and the size of the trap orifice, which is why failed-open traps on high-pressure lines come first.
Failed closed (plugged or blocked). Condensate backs up. A heat exchanger or jacket heats slowly or not at all, and a steam main collects water that causes water hammer. On an outdoor line that sits idle, trapped condensate can freeze and split the pipe.
How are steam traps tested?
- Ultrasound. An ultrasonic listener on the trap body hears the flow inside. A healthy cycling trap opens and closes; a failed-open trap makes a steady rush of steam. This is the main test.
- Temperature. A contact thermometer or infrared reading upstream and downstream shows traps that are cold, which means failed closed, blocked upstream, or the line is out of service. Temperature alone cannot confirm a blow-through, because condensate draining at saturation is the same temperature as the steam. That is why temperature is paired with ultrasound.
- Visual, where a test valve exists. Condensate discharged to atmosphere makes a lazy cloud of flash steam. Live steam leaves as a clear jet near the outlet before it turns white. This takes experience, and the discharge is hot.
Safety comes first. Wear a face shield and gloves near test valves. Never remove a trap cap, strainer, or trap under pressure; isolate the trap, relieve the pressure, let it cool, and follow lockout/tagout and your site’s procedures before any repair.
How do you run a steam trap program?
- Tag and number every trap. Record location, type, size, pressure, and what it drains.
- Survey on a schedule. Many plants test every trap at least once a year, and high-pressure or process-critical traps more often.
- Log every result. Good, failed open, failed closed, leaking, or out of service, with the date.
- Fix in order. Failed-closed traps causing water hammer or a process problem first, for safety. Then failed-open traps, highest pressure and largest orifice first.
- Check the rest of the station. Strainers ahead of traps, check valves, and back pressure in the return line all affect how a trap works.
- Re-test after repair so the log shows the trap is good.
Steam trap testing is a good operator skill, and McKenna covers trap basics in boiler operator training. For terms like flash steam and back pressure, see the boiler glossary.
What to watch between surveys
- A heavy steam plume from the condensate receiver vent.
- Water hammer, especially at startup or when a load valve opens.
- Heat exchangers or jackets that heat slowly or unevenly.
- Makeup water meter readings climbing week over week.
- Condensate pump noise or cavitation from flashing condensate.
Common questions
How often should steam traps be tested?
Many plants test every trap at least once a year. High-pressure traps and traps on critical process equipment are often tested more frequently. The log from each survey shows whether the interval is right for your plant.
Can you find a failed trap with a temperature gun?
A temperature reading finds traps that are cold, which usually means failed closed or no steam reaching them. It cannot reliably find a trap blowing steam, because draining condensate and steam are the same temperature. Ultrasound is needed for that.
Which failed traps should be fixed first?
Fix failed-closed traps that cause water hammer or stop a process first, because water hammer can break fittings. Then fix failed-open traps, starting with the highest pressure and largest orifice, since they lose the most steam.
Why does our condensate receiver vent blow steam?
Some flash steam is normal when hot condensate drops to atmospheric pressure. A heavy, continuous plume usually means one or more traps are blowing live steam into the return. A trap survey finds which ones.
Do failed steam traps affect the boiler?
Yes. Lost steam and condensate increase makeup water, which brings more hardness and oxygen into the boiler and raises chemical use and blowdown. Flashing condensate can damage feed pumps, and the boiler fires harder to carry the same load.
McKenna technicians test each trap with ultrasonic and temperature checks, note line pressures, and report which traps have failed open, failed closed, or are leaking. To schedule a survey, see steam trap audits or call (323) 987-1816.





